00453故障码怎么解决 ,00457故障码怎么解决
今天给各位分享00453故障码怎么解决的知识，其中也会对00457故障码怎么解决进行解释，如果能碰巧解决你现在面临的问题，别忘了关注本站，现在开始吧！
本文目录一览：
奥迪00453是怎么故障
这是一个信息码00453故障码怎么解决，告诉00453故障码怎么解决你AWD（全驱动）由于温度过高导致功能受限制。
用什么解码器读出来00453故障码怎么解决的00453故障码怎么解决？
建议换一个解码器再读。
斯柯达自动变速箱00453 超温功能限制是什么
水温超过变速箱电脑里预设的温度，为防止变速箱损坏电脑对自动变速箱进行保护，让其只有4档，四档起步，2000转车子只能跑60码
新帕萨特变速器为何持续“高烧”不退？
故障现象00453故障码怎么解决：该车自动变速器最近一段时间以来一直持续“高烧”不退，吃了很多“药”（更换ATF润滑油等相关部件），而且也已经做了一次“手术”（更换变速器变矩器和阀体等部件），但“高烧”问题一直得不到根治。当变速器高烧至116℃左右时变速器控制单元会记录一个“关于变速器超温功能受限”的故障码（如图1所示），此时发动机会出现动力不足且油门加不起来的故障现象。
图1 故障码
删除故障存储器中的故障码进行路试，刚开始试车时变速器表现一切正常，可后来确实感觉发动机加速无力和油门加不起来的情况，同时变速器表现为换挡延迟且有轻微的冲击感。用诊断仪检测到的变速器油温信息是116℃，同时00453故障码再次重现。考虑到该车已经行驶100000km且一次也没有对变速器有过养护记录，因此决定还是保守治疗，这样征得用户同意后先做一个保养换油试试。
可是更换完带油温传感器的线束后，经试车“高烧”故障还是没有得到解决，这就奇怪了！还有哪些原因会导致变速器持续“高烧”呢00453故障码怎么解决？变速器本身的问题还是散热系统的问题呢。不管咋样还是按照先简单后复杂、先外后内的检修方法进行。因为变速器在每天初次使用时都是正常的，这说明变速器内部机械元件应该不会有大问题。冷静分析能够导致变速器高温的可能原因也就是：①冷却系统故障；②变速器的变矩器TCC锁止不良；③变速器个别挡位打滑；④变速器缺少高速挡等。经每次试车结果可以排除③和④的故障可能，变速器既没有打滑情况，更没有缺少高速挡的情况，因此如果说变速器真实存在“高烧”故障的话，要么冷却系统故障，要么变矩器TCC闭锁故障。在这种情况下，大家毫不犹豫的又把自动变速器的独立冷却器（如图3所示）给换掉了。
图3 更换的变速器冷却器
用户用了仅仅还不到一个礼拜，车辆再次因变速器“高烧”而返厂，看来之前我们还是没有找到变速器持续“高烧”的真正病因。但在我们之前的故障评估中也仅剩下变矩器TCC闭锁这一块了。为了方便节省时间，这次决定直接更换一个变矩器总成试试，这样比较快一些。把变速器拆下来直接更换一个拆车的成色比较好的变矩器总成（如图4所示），可是装车后试车变速器再次出现“高烧”症状。难道不是变矩器TCC闭锁不良的原因，还是我们更换的变矩器本身有问题。种种现象表明变矩器故障的可能性极小，因为不可能两个变矩器表现情况都一模一样。在实际试车观测动态数据流时，小油门或正常驾驶时3挡、4挡、5挡、6挡时TCC闭锁情况非常好，只有大油门操作时变矩器TCC有不锁的情况或锁止有轻微打滑的情况。
图4 更换的变矩器
既然变矩器没有任何问题，那还能有哪里会导致变速器持续“高烧”不止呢？难道是液压控制单元（阀体）提供的变矩器TCC闭锁油压不够，导致TCC闭锁不良而出现功率损失，从而导致持续“发烧”不止。听同行讲09G变速器阀体故障确实比较多，但大多数都是表现换挡品质不良故障。当然也是确实没有其他办法了，在这种情况下决定更换阀体（如图6所示）。
图6 更换的阀体总成
如果是控制单元确实存在问题，那一定是一个假的温度信号，所以接下来只要我们能够确定变速器真实温度，是不是真的到“高烧”程度了，如果真实温度确实不高我们再研究更换控制单元也不迟，如果确实还是在高烧，那么我们就要重新梳理一下思路了。
在仔细检查变速器冷却系统时，发现来自发动机水箱的冷却液管路中有一个东西（如图7所示），后来才知道是一个节温器（如图8所示）。
图7 变速器冷却管路中的节温器
图8 节温器总成
故障排除：重新更换节温器后变速器持续“高烧”不止的顽症终于得到根治。至此持续多日的维修也终于告一段落。
故障总结：本来在故障可能分析中没有遗漏，但为什么一个持续“高烧”不止故障迟迟得不到解决呢？那就是大家忽略了来自发动机冷却管路中还安装了一个节温器，安装节温器的目的是当自动变速器在低温状态时让ATF实现一个快速加热过程。但由于它的损坏相当于持续在给变速器加热，因此让变速器在高温状态下得不到冷却过程，从而让变速器持续“高烧”不止。通过这个案例也在给大家一个提醒，那就是自动变速器的温度管理功能可能会带来的一些问题。
大众途锐故障码查找
00000:Output ends
00001:Brake control unit
00002:Gearbox control unit
00237:ABS Solenoid valve front left-N59
00238:ABS Solenoid valve front right-N58
00239:ABS solenoid valve rear left-N57
00240:ABS solenoid valve rear right-N56
00241:Trac.contr.press.regulating valve-N238
00242:Engine throttle back valve-N237
00243:Engine brake
00244upply voltage for ABS valves fr+rl
00245upply voltage for ABS valves fl+rr
00246:Earth for ABS valves fr+rl
00247:Earth for ABS valves fl+rr
00248:Gearbox switch-E206
00250witch for off-road operation-E207
00254:Traction control setting missing
00255:Valves for ABS
00257:ABS inlet valve,front left-N101
00258olenoid 1-N88
00259:ABS inlet valve,front right-N99
00260olenoid 2-N89
00261:ABS inlet valve,rear-N103
00262olenoid 3-N90
00263:Gearbox
00264olenoid 4-N91
00265:ABS outlet valve,front left-N102
00266olenoid 5-N92
00267:ABS outlet valve,front right-N100
00268olenoid 6-N93
00269:ABS outlet valve,rear-N104
00270olenoid 7-N94
00271ee Repair Group 01
00273:ABS inlet valve,rear right-N133
00274:ABS inlet valve,rear left-N134
00275:ABS outlet valve,rear right-N135
00276:ABS outlet valve,rear left-N136
00277:ABS inlet/outlet valve,front left-N137
00278:Main ABS valve-N105
00279:Valve 1 for differential lock-N125
00280:Valve 2 for differential lock-N126
00281:Road speed sender-G68
00282:Throttle valve positioner-V60
00283peed sensor front left-G47
00284:ABS inlet/outlet valve,front right-N138
00285peed sensor front right-G45
00286:ABS inlet/outlet valve,rear left-N139
00287peed sensor rear right-G44
00289:ABS inlet/outlet valve,rear right-N140
00290peed sensor rear left-G46
00291ressure switch-F116/Warn. contact-F117
00292:Hydrau1. energy supply pressure level
00293:Multi-function switch-F125
00294ressure switch 1 for gearbox condition
00295ressure switch 2 for gearbox condition
00296:Kick-down switch-F8
00297:Gearbox speed sender-G38
00298witch for differential lock-E121
00299rogramme switch-E122
00300:Gearbox oil temperature sender-G93
00301:ABS return flow pump-V39
00302olenoid valve relay-ABS-J106
00303:Function selection switch-E91
00305:Fuel consumption indicator signal
00306econdary air system Cy1. bank 1
00307econdary air system Cy1. bank 2
00309:Cleaning fluid dispensing pump-V135
00310:Cat. temp. sensor 1-G20
00312:Cat. temp. sensor 2-G132
00313:Catalyst
00314:Ex. gas recirc. two-way valve-N161
00347olenoid 8-N281
00348olenoid 9-N282
00349olenoid 10-N283
00350:Earth return wire,modulating piston
00351:Intermediate shaft speed sender-G265
00448re-press. pump,Haldex coupling-V181
00449re-pressurising pump on
00450re-pressurising pump off
00451:Four-wheel coupling disengaged
00452:Four-wheel coupling engaged
00453:Functional restriction due to high temp.
00454:Four-wheel monitoring
00503:Valve control pump/vent
00504:No.1 cy1. pump/nozzle valve-N240
00505:No.2 cy1. pump/nozzle valve-N241
00506:No.3 cy1. pump/nozzle valve-N242
00507:No.4 cy1. pump/nozzle valve-N243
00508:No.5 cy1. pump/nozzle valve-N244
00509:No.6 cy1. pump/nozzle valve-N245
00512:Hall sender not on reference mark
00513:Engine speed sender-G28
00514:Ignition timing sender-G4
00515:Hall sender-G40
00516:Idling switch-F60
00517:Full throttle switch-F81
00518:Throttle valve potentometer-G69
00519:Intake manifold pressure sender-G71
00520:Air mass/flow meter-G70/G19
00521:CO potentiometer-G74
00522:Coolant temperature sender-G62
00523:Intake air temperature sender-G42
00524:Knock sensor 1-G61
00525:Lambda probe-G39
00526:Brake light switch-F
00527:Intake manifold temperature sender-G72
00528:Altitude sender-F96
00529peed information missing
00530:Throt. positioner/potentiometer-G88
00531:Air mass meter reference voltage
00532upply voltage
00533:Idling speed regulation
00534:Oil temperature sender-G8
00535:First knock regulation
00536:2nd knock regulation
00537:Lambda control
00538:Reference voltage
00539:Fuel temperature sender-G81
00540:Knock sensor 2-G66
00541lide travel potentiometer-G99
00542:Needle lift sender-G80
00543:Maximum revs exceeded
00544:Maximum boost prssure exceeded
00545:Engine/gearbox electrical connection
00546ata cable defection
00547ressure control switch for ABS-F137
00548:Voltage supply for fault memory
00549:Consumption signal
00550:Injection commencement regulation
00551:Catalyst excess temperature
00552:Air flow meter potentiometer-G19
00553:Air mass meter-G70
00554:Lambda regulation II
00555:Lambda probe II-G108
00556:Exhaust gas recirc. potentiometer-G212
00557ower assisted steering/press. switch-F88
00558:Mixt. control lean adj. limit
00559:Mixt. control rich adj. limit
00560:Exhaust gas recirculation system
00561:Mixture adaptation
00562:Oil level/temperature sender-G266
00563:Current consumption display-Y10
00564:Oil temperature sender
00567teering motor activated
00568osition sensors in steering motor
00569teering motor current
00570teering motor relay-J509
00571teering coupling
00572teering position sender-G268
00573teering torque sender-G269
00574rive motor on
00575:Intake manifold pressure
00576:Terminal 15
00577:Knock control cylinder 1
00578:Knock control cylinder 2
00579:Knock control cylinder 3
00580:Knock control cylinder 4
00581:Knock control cylinder 5
00582:Knock control cylinder 6
00583:Knock control cylinder 7
00584:Knock control cylinder 8
00585:Temperature sensor-EGR-G98
00586:EGR system control
00587:Adjustment limit mixture regulation
00588:Airbag igniter-driver side-N95
00589:Igniter 1 for airbag-passenger side-N131
00590:Igniter 2 for airbag-passenger side-N132
00591:Belt switch-driver side-E24
00592:Belt switch-passenger side-E25
00593eat contact switch-passenger seat-F151
00594:Airbag ignition circuit
00595:Crash data stored
00596hort circuit between valve wires
00597iffering wheel speed impulses
00598:Hydraulic/mechanical defect
00599lausibility pressure/brake light switch
00600otentiometer in V68-G92
00601otentiometer in V70-G112
00602otentiometer in V85-G114
00603efroster flap motor in footwell-V85
00604otentiometer in V71-G113
00605:Two-way valve fresh/recirc. air flap-N63
00606:Two-way valve coolant cut-off valve-N147
00607:Ambient temperature indicator-G106
00608:Load state sender-G119
00609:Ignition output 1
00610:ignition output 2
00611:ignition output 3
00612:ignition output 4
00613:ignition output 5
00614:ignition output 6
00615:ignition output 7
00616:ignition output 8
00617:Airbag delay sender left-G104
00618:Airbag delay sender right-G105
00619ender wire,left
00620ender wire,right
00621ressure reducing valve-N155
00622rain water from fuel filter
00623:ABS/gearbox electrical connection
00624:Air conditioner compressor cut-in
00625peed signal
00626:Glow period warning lamp-K29
00627:Water lever sender-G120
00628:Control element setting monitoring
00629:Brake pedal switch-F47
00630:Air conditioner switched on
00633:Igniter wiring/deceleration sender
00634:EDL series resistance-N159
00635:Lambda probe heating before Cat
00636:FR acceleration sender-G121
00637:RL acceleration sender-G122
00638:Engine/gearbox electrical connection 2
00639eceleration sender-G123
00640:Lambda probe heating relay-J278
00641:ATF temperature
00642:EDL changer-over valve front right-N166
00643:EDL valve front right-N167
00644:EDL change-over valve front left-N168
00645:EDL outlet valve front left-N169
00646:ABS-TCS/engine electrical connection 1
00647:ABS-TCS/engine electrical connection 2
00648:Lambda probe heating after Cat
00649:ABS in/outlet valve rear-N160
00650:Clutch pedal switch-F36
00651:Wiring for ignition circuit
00652:Gear monitoring
00653lausibility selector lever/gearbox
00654:Belt tensioner igniter(D.side)-N153
00655:Belt tensioner igniter(P.side)-N154
00656eat occupied sensor-G128
00657ositioning m. for centre outlets-V102
00658:Operating unit
00659elf test
00660:Kickdown switch/throttle valve poti.
00661:Temperature indicator
00662:Rev. counter
00663peedometer
00664:Fuel gauge
00665eat belt warning lamp-K19
00666:Gong
00667:Ambient temperature signal
00668:Vehicle voltage terminal 30
00669econd fault lamp-K97
00670:Throttle valve positioner sender-G127
00671:CCS switch-E45
00672:ABS hyd. pump with series resistance
00673:Operate brake
00674:Release brake
00675:IFL:0V OFL:0V Wheel FL locked
00676:IFL:VBAT OFL:0V Wheel FL locked
00677:IFL:VBAT OFL:VBAT Wheel FL free
00678:IFL:VBAT OFL:0V Wheel FL free
00679:Lambda probe II heating before Cat
00680:IFR:0V OFR:0V Wheel FR locked
00681:IFR:VBAT OFR:0V Wheel FR locked
00682:IFR:VBAT OFR:VBAT Wheel FR free
00683:IFR:VBAT OFR:0V Wheel FR free
00684:Lambda probe II heating after Cat
00685:IRL:0V ORL:0V Wheel RL locked
00686:IRL:VBAT ORL:0V Wheel RL locked
00687:IRL:VBAT ORL:VBAT Wheel RL free
00688:IRL:VBAT ORL:0V Wheel RL free
00689:Unmetered air in intake air system
00690:IRR:0V ORR:0V Wheel RR locked
00691:IRR:VBAT ORR:0V Wheel RR locked
00692:IRR:VBAT ORR:VBAT Wheel RR free
00693:IRR:VBAT ORR:0V Wheel RR free
00694:Lighting/switch and instruments
00695:EDL valves/hyd-p. VBAT wheel FL/FR locked
00696:Valve for pressure reducer left-N170
00697:Valve for pressure reducer right-N171
00698:Increased current draw control unit
00699:Lambda probe after Cat-G130
00700:Lambda probe II afer Cat-G131
00701:Coolant excess temperature test
00702:Fuel composition sender-G133
00703:Idling recognition TV. poti/IDL switch
00704:EDL valves/hyd-p. VBAT wheels locked
00708ANGER fan will be switched on
00709hoto-sensor 2 for sun penetration-G134
00710efrost flap control motor-V107
00711:Left footwell flap control motor-V108
00453故障码指的是什么意思？
建议您用解码仪进行解码，找到故障，去维修店找专业人士为您检测维修，希望我的回答对你有帮助，望采纳
关于00453故障码怎么解决和00457故障码怎么解决的介绍到此就结束了，不知道你从中找到你需要的信息了吗 ？如果你还想了解更多这方面的信息，记得收藏关注本站。
